Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 337

Page: 337 / 2018

DNS Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 11-9

Related Commands

MIB Objects

systemDNS

systemDNSEnableDnsResolver

systemDNSDomainName

systemDNSNsAddr1

systemDNSNsAddr2

systemDNSNsAddr3

systemDNSNsIPv6Addr1

systemDNSNsIPv6Addr2

systemDNSNsIPv6Addr3

ip domain-lookup

Enables or disables the DNS resolver.

ip name-server

Specifies the IP addresses of up to three servers to query on a host
lookup.

ipv6 name-server

Specify the IPv6 addresses of up to three IPv6 DNS servers to query on
a host lookup.

ip domain-name

Sets or deletes the default domain name for DNS lookups.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 337 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: