manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 333 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 333

DNS Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 11-5

ipv6 name-server

Specifies the IPv6 addresses of up to three IPv6 DNS servers to query on a host lookup.

ipv6 name-server server-ipv6_address1 [server-ipv6_address2 [server-ipv6_address3]]

Syntax Definitions

server-ipv6_address1

The IPv6 address of the primary IPv6 DNS server to query for host 
lookup. Specifying the primary IPv6 DNS address is mandatory.

server-ipv6_address2

The IPv6 address of the secondary IPv6 DNS server to query for host 
lookup. This server will be queried only if the desired host name is not 
able to be resolved by the primary IPv6 DNS server. A second IPv6 
address is optional.

server-ipv6_address3

The IPv6 address of the IPv6 DNS server with the lower priority. This 
server will be queried only if the desired host name is not able to be 
resolved by both the primary and secondary IPv6 DNS servers. A third 
IPv6 address is optional.

Defaults

N/A

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

•

Configuration of the DNS resolver to resolve any host query requires that you first set the default 
domain name with the 

ip domain-name

 command and enable the DNS resolver function with the 

ip 

domain-lookup 

command before you specify the IPv6 addresses of the IPv6 DNS servers by using the 

ipv6 name-server

 command.

•

You cannot use multicast, loopback, link-local and unspecified IPv6 addresses for specifying IPv6 
DNS servers.

•

You can configure up to three IPv6 DNS servers and three IPv4 DNS servers in a switch.

Examples

-> ipv6 name-server fec0::2d0:d3:f3fc

-> ipv6 name-server fe2d::2c  f302::3de1:1 f1bc::202:fd40:f3

Release History

Release 6.6.1; command was introduced.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments