manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 331 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 331

DNS Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 11-3

ip name-server

Specify the IP addresses of up to three servers to query on a host lookup.

ip name-server server-address1 [server-address2 [server-address3]]

Syntax Definitions

server-address1

The IP address of the primary DNS server to query for host lookup. This 
is the only address that is required.

server-address2

The IP address of the secondary DNS server to query for host lookup. 
This server will be queried only if the desired host name or host IP 
address is not located by the primary DNS server. A second IP address 
is optional.

server-address3

The IP address of the DNS server with the lower priority. This server 
will be queried only if the desired host name or IP address is not located 
by the primary and secondary DNS servers. A third IP address is 
optional.

Defaults

N/A

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

•

Configuration of the DNS resolver to resolve any host query requires that you first set the default 
domain name with the 

ip domain-name

 command and enable the DNS resolver function with the 

ip 

domain-lookup 

command before you specify the IP addresses of the DNS servers by using the 

ip 

name-server

 command.

•

You can configure up to three IPv4 DNS servers and three IPv6 DNS servers in a switch.

Examples

-> ip name-server 189.202.191.14 189.202.191.15 188.255.19.1 

-> ip name-server 10.255.11.66

Release History

Release 6.6.1; command was introduced.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments