background image

 

 

P

REPARATION FOR 

U

SE

PAY ATTENTION

FILL THE HOPPERS ONLY 

WHEN THE MACHINE IS OFF

 

Open the door and locate extensions capacity on top of the hopper. 
Unlock the latch A (white slide) of the cover and slide 
the latter fully out towards the outside, until is positioned as 
a pilot chute: pour into the hopper the coins or tokens to be 
dispensed as change. 
Unlock again the latch A and slide the cover back 
to “closed” position. 
Close the tiltable front flap of the machine. 

Plug the power cable in, and turn the main switch on. 

Component check and self-setting shall start automatically. At the end, a message will inform 
that the machine is ready for operation, showing what coin(s) (tokens) value(s) will be paid in 
exchange for notes and coins introduced, as well as a welcome wording. 

 

This message takes shifts with: 

 

As soon as the control board enables the note acceptor, the latter’s front slot flashes once in 
blue colour for each enabled note, or once in red for each disabled note. For instance, if the 5, 
10, 20 Euro notes are enabled, and the 50 and 100 Euro notes are disabled, the front slot will 
flash 3 times in blue colour and 2 (twice) in red.  The machine is now ready to operate. 

 

6.

 

Operation 

Three buttons are available: “1” and “2” (“SEL-“ and “SEL+”) allow the User to choose the 
coin (or token) value he wants back as change; third button allows the user to choose the 
language he wants on the display (English, French, German, Italian and Dutch are available. 
Ask before placing order for other languages options). The machine offers two different 
modes of operation, depending on whether the operation mode is set to AUTOMATIC MODE 
or to MANUAL MODE.  

A

UTOMATIC 

M

ODE 

- when a note or coin is inserted, the credited amount is displayed, and the 

control board starts the pay-out by the hopper(s). The machine combines the coins contained 
in the hoppers. If the machine is set to Change, all the tokens that can be bought by 
the inserted sum will be dispensed, with the back change in addition.

 

At the end of the payout 

cycle, the display will show both the inserted amount as well as the amount paid out. 

PAY-OUT  TABLE  ENABLED  AND  PROGRAMMED

:

 when a note or coin is inserted, the 

display shows the credited amount, and the machine shall automatically pay-out according to 
the combination that the Operator has pre-programmed for the amount inserted (see section 

7.3.5 B

 DISPENSING MODE SETUP

). By enabling such pay-out table from the menu settings, 

the User will only be able to get the tokens and/or coins that can be bought by the inserted 
money, according to the combination preset by the Operator. See the setting flow-chart in 
section 7.3.5 B

.

  

 

 

 

 

 

 

EROGA MONETE DA

 

1,00 € - 2,00 €

 

CHANGEONE

 

Promo

 

Summary of Contents for Spike CM Arm































Reviews: