manualshive.com logo in svg

Albedo xGenius, User Manual, Page: 9 / 322

Share
Download
Albedo xGenius User Manual Download Page 9

vii

Frequency Offset Generation .................................................................... 262
Wander Generation .................................................................................... 263
Operation in IP Through Mode .................................................................. 264
ESMC Generation and Analysis ................................................................ 265

Chapter 11: Test Management.............................................................................. 269

Generating Reports .................................................................................... 269
File Management ........................................................................................ 271

Saving Configurations ....................................................................... 271
Renaming Files ................................................................................. 272
Deleting Files .................................................................................... 272
Exporting Files to External Devices .................................................. 272
Importing Configurations ................................................................... 273
Verifying the Current Disk Usage...................................................... 273
Configuring What to Do When the Disk is Full .................................. 274
Using the Embedded Web Server..................................................... 274

Programming Tests.................................................................................... 275
Using the System Menu ............................................................................. 277

Using the Network............................................................................. 279
Installing Software Options ............................................................... 285
Upgrading the Power Management .................................................. 286
Using NTP and GPS/NMEA for System Clock Synchronization ....... 287

Using the Remote Control ......................................................................... 289

Appendix A: Technical Specification................................................................... 291

General ........................................................................................................ 291
Operation Modes ........................................................................................ 291
Clock............................................................................................................ 292

Rubidium Reference ......................................................................... 292
Built in GNSS .................................................................................... 292
GNSS Compact Antenna .................................................................. 292
Clock Reference Inputs..................................................................... 292
Clock Reference Outputs .................................................................. 293

Ethernet PHY............................................................................................... 293

Auto-Negotiation ............................................................................... 293
Synchronous Ethernet....................................................................... 293
Power over Ethernet ......................................................................... 294

Ethernet MAC.............................................................................................. 294

Summary of Contents for xGenius



































































































































































































































































































































Reviews:

No comments