manualshive.com logo in svg

Albedo xGenius, User Manual, Page: 5 / 322

Share
Download
Albedo xGenius User Manual Download Page 5

iii

Table Of Contents

Chapter 1: Introduction ............................................................................................. 1

Important Notice ............................................................................................. 2

Warranty................................................................................................ 2
Safety .................................................................................................... 3
WEEE Notice ........................................................................................ 3

The Tester ....................................................................................................... 3

Test Connector Panel ........................................................................... 4
Platform Connector Panel ..................................................................... 6

The Graphical User Interface......................................................................... 6

The Home Panel ................................................................................... 6
The Menu Structure .............................................................................. 9
The Summary and LEDs Tabs............................................................ 11
Recently Used Panel and Menu Tree ................................................. 12
Predefined Tests ................................................................................. 13

Running Tests............................................................................................... 13
Upgrading the Unit ....................................................................................... 14

Chapter 2: Connection to the Network .................................................................. 17

Setting the Operation Mode......................................................................... 17
Connecting the Tester to the Network........................................................ 20

Configuring the Connector .................................................................. 21
Using the SFP / SFP+ Ports................................................................ 22
Configuring Port A and Port B Auto-negotiation Parameters .............. 24

Entering the Port Local Settings................................................................. 27
Using Pluggable Hardware Modules (PHMs) ............................................. 30
Using the Traffic Reflector........................................................................... 30
Testing with an External Clock Reference ................................................. 32

Using PPS / ToD and Frequency References..................................... 38
Configuring the Built in GNSS Receiver.............................................. 41
Using the Holdover Mode.................................................................... 45

Using the Clock Reference Output ............................................................. 48

Summary of Contents for xGenius



































































































































































































































































































































Reviews:

No comments