Albatron P4M800 Pro User Manual Download Page 48

Page: 48 / 50

8. The initial AWARD BIOS FLASH screen (shown below-left) will appear and prompt you with the
message, “Do you want to save BIOS?” Type “

” (

Note:

Typing “Y” is only used when saving the BIOS

from the onboard BIOS to the floppy disk).

The next screen (shown above-right) will display a message “Press ’Y’ to Program or ‘N’ to Exit”. Then
type ‘

’ to begin the onboard BIOS flash procedure.

9. The flashing procedure will take several minutes and will show its progress on the screen. After the
flash BIOS procedures have completed, press ‘

’ to reboot the system.

When the flash process is complete, press ‘F1’

Attention

While processing the flash BIOS procedures, DO NOT power off or
restart your system. Otherwise, it may damage the onboard BIOS.

Type N

Type Y

Summary of Contents for P4M800 Pro



















































Search results

Summary of Contents for P4M800 Pro

Reviews:

Related manuals for P4M800 Pro

Brands by name

Popular brands

Albatron P4M800 Pro, User Manual

Search results

Summary of Contents for P4M800 Pro

Reviews:

Related manuals for P4M800 Pro

Brands by name

Popular brands