Albatron KM18G PRO User Manual Download Page 7

Page: 7 / 54

KM18G PRO/ KM18G PRO II

BUS Slots:

1 AGP slot (1.5V only)

Three 32-bit PCI bus slots

Flash Memory:

Supports flash memory functionality

Supports ESCD functionality

Hardware Monitor Function:

Monitors CPU and System fan Speeds

Monitors System Voltage

Infrared:

Supports IrDA Version 1.0 SIR Protocol with a maximum baud rate of up to 115.2 Kbps

Supports SHARP ASK-IR Protocol with maximum baud rate of up to 57600 bps

Universal Serial Bus:

Supports USB 2.0 Enhanced Host Controller Interface (EHCI) and dual USB 1.1 Open
Host Controller Interface (OHC1)

Supports up to six USB ports for USB interface devices

IEEE 1394 Serial Bus (for KM18G PRO II only):

Supports two IEEE 1394 ports for 1394 interface devices

Supports 400/ 200/ 100 Mbps serial date rates

I/O facilities:

One multi-mode Parallel Port capable of supporting the following specifications:

1. Standard & Bi-direction Parallel Port

2. Enhanced Parallel Port (EPP)

3. Extended Capabilities Port (ECP)

Supports two serial ports, 16550 UART (one on back panel and one on front panel)

Supports Infrared Data Transmission using IrDA

Supports PS/2 mouse and PS/2 keyboard and one Game port

Supports 360 KB, 720 KB, 1.2 MB, 1.44 MB, and 2.88 MB floppy disk drives

Summary of Contents for KM18G PRO























































Search results

Summary of Contents for KM18G PRO

Reviews:

Related manuals for KM18G PRO

Brands by name

Popular brands

Albatron KM18G PRO, User Manual

Search results

Summary of Contents for KM18G PRO

Reviews:

Related manuals for KM18G PRO

Brands by name

Popular brands