Akuvox R28 Series Administrator'S Manual Download Page 28

Page: 28 / 122

R28 Door Phone Administrator Guide

www.akuvox.com

•

PromptVolume:

adjust the prompt volume, which includes various types of prompt

sound for door open success and failure, ringback, temperature measurement sound,
etc.

8.1.1 Open Door Tone Configuration

You can not only enable or disable the Open Door Tone but also controls the prompt words
that accompany the tone on the web

Phone > Audio > Open Door Warning

interface.

Parameters Set-up:

•

Open Door Inside Tone

: enable it so that you can hear the open door tone when you

open the door by pressing the exit button.

•

Open Door Outside Tone

: enable it so that you can hear the open door tone when you

open the door using the access method on the doorphone.

•

Open Door Failed Tone

: enable it so that you can hear the open door failure tone

following the open door failure.

8.2 Upload Tone Files

You can configure the door phone ringback tone and other tones related to the door
opening.

8.2.1 Upload Open Door Tone and Ringback Tone

You can customize the tone of door open successful/failed if you need. The outside tone
is used to open the door via card or DTMF or PIN code. The inside tone is used to open the

Summary of Contents for R28 Series


























































































































Search results

Summary of Contents for R28 Series

Reviews:

Related manuals for R28 Series

Brands by name

Popular brands

Akuvox R28 Series, Administrator'S Manual

Search results

Summary of Contents for R28 Series

Reviews:

Related manuals for R28 Series

Brands by name

Popular brands