Aktobis WDH-C03 User Manual Download Page 7

 

Aktobis AG,  Borsigstr. 20,  D-63110 Rodgau / Germany 

www.AKTOBIS.de

 

Email: [email protected] 

 
 

 
5.) Setting the various operating modes (functions) 
 

Press the Settings button          in succession for the desired setting: 

 

 

 
 
 
 
 
 
 

 

Furthermore, combinations can be set that enable joint operation of the individual functions ! 
 

6.) Activate the automatic air sensor 
 

Press the Auto button         on your air purifier. The air sensor thus switches on and automatically starts measuring 
the air quality. There are 4 possible results of the determined air quality (see diagram below): 

 

Please note that the proper air sensor function is only available after approx. 3 minutes ! 

 

 

 
 

 

No bar (

PM-value 0-30

)  

=    Very good air quality 

>     Air circulation extremely low

 

 
 

 

3 bars (

PM-value 30-75

=    Light air pollution 

 

>     Air circulation jumps to level 1 (weak) 

 

 

 

6 bars (

PM-value 75-150

=    Average air quality   

>     Air circulation jumps to level 2 (medium) 

 

 

 

9 bars (

PM-value over 150

=    Bad air quality 

 

>     Air circulation jumps to level 3 (strong) 

 
In addition to the air quality display shown above, you will also see a PM value in the display. You can read at the 
top which air quality category the respective PM value falls into. 
 
Note: The air sensor is located at the front right behind the filter flap and reacts mainly to odors and slightly to 
particles in the air and thus always gives only a tendency of the air quality. Since it is a tendency (similar to a 
weather station), this function cannot provide a 100% reliable statement about pollutants in the room air or about 
the entire area of a room. 
 
From a humidity of approx. 80% r.l. upwards, the air sensor probe may malfunction. In this case, we ask you to 
dispense with the air sensor function (Auto). 
 
Furthermore, stronger operating fluctuations may occur from time to time, as the air sensor probe is exposed to the 
air draught. 
 
 

This function generates more than 5 million anions per second, which proactively 
combat smoke and other particles in the room. 

Eliminates many of the most common types of bacteria and viruses. Furthermore, 
the UV light ensures that the filters themselves can never become a breeding 
ground for germs ! (There is a 6W UV lamp installed behind the filters). 

Air quality display 

Summary of Contents for WDH-C03













Reviews: