AKG WMS 40 SINGLE/DUAL User Instructions Download Page 3

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Parts 74, 15, and 90 of the FCC Rules. These limits are designed to provide reasona-
ble protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no gua-
rantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference by one or more of the fol-
lowing measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

Consult the dealer or an experienced radio/TV technician for help.

Shielded cables and I/O cords must be used for this equipment to comply with the relevant FCC
regulations.
Changes or modifications not expressly approved in writing by AKG Acoustics may void the user’s
authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two con-
ditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

1 Safety and Environment

1.1 Safety

1.2 Environment

2.1 Introduction

1. Spill no liquids on the equipment and do not drop any objects

through the ventilation slots in the equipment.

2. Do not place the equipment near heat sources such as radiators,

heating ducts, or amplifiers, etc. and do not expose it to direct sun-
light, excessive dust, moisture, rain, mechanical vibrations, or
shock.

1. Be sure to dispose of used batteries as required by local waste dis-

posal rules. Never throw batteries into a fire (risk of explosion) or
garbage bin.

2. When scrapping the equipment, remove the batteries, separate the

case, circuit boards, and cables, and dispose of all components in
accordance with local waste disposal rules.

Dear Customer:
Thank you for purchasing an AKG product. This Manual contains
important instructions for setting up and operating your equipment.
Please take a few minutes to read the instructions below carefully

before operating the equipment.

Please keep the Manual for future

reference. Have fun and impress your audience!

2 Description

16

Summary of Contents for WMS 40 SINGLE/DUAL















Reviews: