background image

29

4.1.3 Extra Functions
• NAME

Diagram 12: Entering a new
receiver name.

• STATUS

Diagram 13: Warning messages.

If you have not stored a receiver name
yet, you can use the "NAME" screen to
assign a new name to your receiver.

Use 

and 

to select the first charac-

ter.

Use 

and 

to select the second char-

acter, etc….

… to the sixth character.

SAVE >Y<:

save your setting.

SAVE >N<:

reject your setting.

>DELETE<:

delete all names.

The "STATUS" screen lets you activate a visual warning that alerts you to selectable critical system con-
ditions. If one of the selected conditions occurs, the display backlighting will change from green to red
and a warning message will appear on the display that describes the current condition. The warning mes-
sages appear in the order of priority:

1. "LOW.BAT":

Transmitter battery capacity is low.

2. "AFCLIP":

Audio overload.

3. "RF.LOW":

Received signal field strength is so low that the receiver audio output has been muted.

- "BAT":

The battery inside the trans-

mitter will be dead in about 60 minutes.
The related message on the display is
"LOW.BAT".

- "AF":

The received audio signal drives

the receiver into clipping. The related
message on the display is "AFCLIP".

- "RF":

The field strength of the

received RF signal is so low that the
receiver audio output is muted to pre-
vent unwanted noise. The related mes-
sage on the display is "RF LOW".

SAVE >Y<:

save your setting.

SAVE >N<:

reject your setting.

All selected warning functions are active in both LOCK and SETUP modes. In SETUP mode, however,
the warning functions will be automatically deactivated every time you make an adjustment.
To delete the warning message from the display, press the 

key briefly. This will bring up the next warn-

ing message or, if no other critical system conditions were detected, the normal screen. The display
backlighting will revert to green.

EXTRA

X-TRA

>NAME<

X-TRA

NAME

"B>_<"

NAME

">BEN_ _ _<"

SAVE >N<

>X-TRA<

EXTRA

X-TRA

>DELETE<

>X-TRA<

SAVE >Y<

>X-TRA<

NAME

>_<

NAME

"BEN _ _ _"

EXTRA

X-TRA

>NAME<

X-TRA

>STATUS<

X-TRA

EXTRA

X-TRA

SAVE >N<

>X-TRA<

SAVE >Y<

>X-TRA<

BAT.>OFF<

X-TRA 

AF.>OFF<

X-TRA 

AF.>ON<

X-TRA 

RF>OFF<

X-TRA 

RF.>ON<

X-TRA 

BAT.>ON<

X-TRA 

AKG WMS 450 V 1.10

4  Operating Notes

Summary of Contents for HT 450

























Reviews: