AKE PowerCom plus Series, Operating And Installation Instructions

Page: 22 / 32

Cable or Bluetooth-to-helmet
If the blue wire is connected to battery negative pole (black), the system is
automatically switched-off if no helmet is connected and the monitor for the
microphone switch is active. This functions are not possible when using Bluetooth-
to-the-helmets. To use this feature cut off the blue wire! If other wired helmets are
used, the input sensitivity can be adjusted by connecting to battery positive pole.
For pairing / operate the Bluetooth-to-helmet connections please read the manual
"PB-HC2 and integrated PowerCom Bluetooth Gateway".
With this connection it is possible to mute the icrophone-switch-voice-monitor
with Bluetooth-to helmet for clear sound and switch off the GPS signal for pillion
(put it into the background, while talking).
“ Relais control line ”
(blue
wire connected)
Additional comfort functions
m
Automatic power-on for additional equipment
The connection (green wire) is connected to the battery
negative pole at the activated system. With a relay cable set additional equipment
like car radio or two-way radio can be activated automatically (master/slave
function), for this feature the automatic helmet detection has to be activated
.
22
Fuse max 1A!
E
N
G
L
IS
H
The power connections
(12V)
With Bluetooth to helmet and weak battery connect the red wire via a separate
switch and turn on this only after the engine is started!
Cable or Bloetooth-to-helmet
bridge
icrophone-switch-voice-monitor
)
connect with GND pairing
red ignition or battery positive pole
Tip: Some modern motorbikes, the font light and other is switched on only
after the engine is started. Then you can supply the red wire with this.
black battery negative pole
blue
connected to battery minus - when using cable to the helmets
cut through - when using Bluetooth to the helmets
connected to battery plus - compatibility mode for other headsets
yellow Comfort functions , connect to battery neg. pole or chassis to switch off the
m and mute the GPS signal for the pillion
green Relay control line , optional (only necessary when using a relay cable set for
automatic accessory activation
violet Bluetooth AG int. control line , optional, for
Attention, when working at the
battery, always separate the negative
conductor first, risk of short circuit!
Cable or Bluetooth-to-helmet
If the blue wire is connected to battery negative pole (black), the system is
automatically switched-off if no helmet is connected and the monitor for the
microphone switch is active. This functions are not possible when using Bluetooth-
to-the-helmets. To use this feature cut off the blue wire! If other wired helmets are
used, the input sensitivity can be adjusted by connecting to battery positive pole.
For pairing / operate the Bluetooth-to-helmet connections please read the manual
"PB-HC2 and integrated PowerCom Bluetooth Gateway".
With this connection it is possible to mute the icrophone-switch-voice-monitor
with Bluetooth-to helmet for clear sound and switch off the GPS signal for pillion
(put it into the background, while talking).
“ Relais control line ”
(blue
wire connected)
Additional comfort functions
m
Automatic power-on for additional equipment
The connection (green wire) is connected to the battery
negative pole at the activated system. With a relay cable set additional equipment
like car radio or two-way radio can be activated automatically (master/slave
function), for this feature the automatic helmet detection has to be activated
.
22
Fuse max 1A!
E
N
G
L
IS
H
The power connections
(12V)
With Bluetooth to helmet and weak battery connect the red wire via a separate
switch and turn on this only after the engine is started!
Cable or Bloetooth-to-helmet
bridge
icrophone-switch-voice-monitor
)
connect with GND pairing
red ignition or battery positive pole
Tip: Some modern motorbikes, the font light and other is switched on only
after the engine is started. Then you can supply the red wire with this.
black battery negative pole
blue
connected to battery minus - when using cable to the helmets
cut through - when using Bluetooth to the helmets
connected to battery plus - compatibility mode for other headsets
yellow Comfort functions , connect to battery neg. pole or chassis to switch off the
m and mute the GPS signal for the pillion
green Relay control line , optional (only necessary when using a relay cable set for
automatic accessory activation
violet Bluetooth AG int. control line , optional, for
Attention, when working at the
battery, always separate the negative
conductor first, risk of short circuit!
Cable or Bluetooth-to-helmet
If the blue wire is connected to battery negative pole (black), the system is
automatically switched-off if no helmet is connected and the monitor for the
microphone switch is active. This functions are not possible when using Bluetooth-
to-the-helmets. To use this feature cut off the blue wire! If other wired helmets are
used, the input sensitivity can be adjusted by connecting to battery positive pole.
For pairing / operate the Bluetooth-to-helmet connections please read the manual
"PB-HC2 and integrated PowerCom Bluetooth Gateway".
With this connection it is possible to mute the icrophone-switch-voice-monitor
with Bluetooth-to helmet for clear sound and switch off the GPS signal for pillion
(put it into the background, while talking).
“ Relais control line ”
(blue
wire connected)
Additional comfort functions
m
Automatic power-on for additional equipment
The connection (green wire) is connected to the battery
negative pole at the activated system. With a relay cable set additional equipment
like car radio or two-way radio can be activated automatically (master/slave
function), for this feature the automatic helmet detection has to be activated
.
22
Fuse max 1A!
E
N
G
L
IS
H
The power connections
(12V)
With Bluetooth to helmet and weak battery connect the red wire via a separate
switch and turn on this only after the engine is started!
Cable or Bloetooth-to-helmet
bridge
icrophone-switch-voice-monitor
)
connect with GND pairing
red ignition or battery positive pole
Tip: Some modern motorbikes, the font light and other is switched on only
after the engine is started. Then you can supply the red wire with this.
black battery negative pole
blue
connected to battery minus - when using cable to the helmets
cut through - when using Bluetooth to the helmets
connected to battery plus - compatibility mode for other headsets
yellow Comfort functions , connect to battery neg. pole or chassis to switch off the
m and mute the GPS signal for the pillion
green Relay control line , optional (only necessary when using a relay cable set for
automatic accessory activation
violet Bluetooth AG int. control line , optional, for
Attention, when working at the
battery, always separate the negative
conductor first, risk of short circuit!
+12V
GND
GND
Cut through if using with
Bluetooth to Helmet
violet
blue
black
red
yellow
green