Akai VS-K207M-E3, Operator'S Manual

Page: 22 / 28

20
--:-- --:-- ------ --
13:00 14:30 1 23 MON
--:-- --:-- ------ --
--:-- --:-- ------ --
--:--
--:-- ------ --
--:-- --:-- ------ --
--:--
--:-- ------ --
--:-- --:-- ------ -- -
-
--
-
--
LP
SELECT :
EXIT : MENU
/ ENTER
TIMER REC SET
DATE 23 MON
11:30
--:--
3 TV3
START
END
CH
SELECT :
SET :
EXIT : MENU
SP SPEED
/ 0Ð9
TIMER REC SET
DATE 23 MON
13:00
1 NRK
START
END
CH
SELECT :
SET :
EXIT : MENU
LP SPEED
OK : ENTER
14:30
Timer Recording
Timer recording can be programed on the TV-
screen with the remote control. The built-in
timer allows automatic unattended recording
of up to 8 programs within 1 month.
Preparation
• Turn on the TV, and select the AV-program position on TV.
•
Load a video cassette with the erase prevention tab intact.
•
Make sure with CALL that the time and date are
correct.(see page 18).
5
6
7
Note:
•
In the event of a power failure the data of the
automatic recording will be maintained in the built-
in memory for about 30 minutes. Also, the clock
will continue to run for this period of time. Thereafter
the data will be deleted. When the power resumes,
the time display will blink indicating that the timer
setting will have to be set.
• In case of the timer recording from the scart socket
proceed as follows: When "CH" is blinking in picture
4, press AV repeatedly until AU appears.
•
If the clock symbol blinks when the timer recording
is completed, the TV program has not been
completely recorded because of an insufficient
tape supply.
Example: Timer recording for channel 1, 13:00 to
14:30 with Tape speed LP on timer program number 1.
1
Press MENU. Press
or
repeatedly until the
dot before TIMER
REC SET blinks. Then
press ENTER.
2
3
4
Set the Starting time (13:00), ending time
(14:30), channel (1 RTP1) and Tape speed (LP)
in the same way as the step 3.
Each line stand for
one program of the 8
memories. Select one
line with or
. Then press
ENTER.
Set the desired date
with / or 10
number buttons.
Then press to
accept it.
Press ENTER to accept them.
TIMER REC SET
VCR EXTENSION
CHANNEL SETUP
SYSTEM SETUP
SELECT :
ENTER : ENTER
MENU EXIT :
SHARPNESS
--:--
--:-- ------ --
--:-- --:-- -- ------
--:-- --:-- -- ------
--:--
--:-- -- ------
--:--
--:-- ------ --
--:-- --:-- ------ --
--:-- --:-- ------ --
--:-- --:-- ------ --
/ ENTER SELECT :
EXIT : MENU
-
-
-
-
-
-
-
-
PRESS T-REC
FOR TIMER RECORDING
• In case of an erroneous
input press to go back to before step
and enter again.
The every channel will
appear in the back-
ground of this setting
screen.
The message
"PRESS T-REC
FOR TIMER RE-
CORDING" will ap-
pear on TV-screen.
You can turn on the timer right now or later by
pressing of TIMER REC or
.
It was not until you turn on the timer that
recording will automatically start at the
programmed time.
• If the cassette is ejected, the erase prevention
tab of the cassette may be removed.(see
page 14)
• As long as the timer is activated (clock symbol
will appear), you cannot use the VCR. If you
want to use the VCR, press TIMER REC at
first to deactivate the timer.
To enter other
programs, repeat
steps 2 through 4.
Or, press MENU
repeatedly until the
TV-picture appears.
As soon as timer is set,
clock symbol will appear
Note: If any button is not pressed within 60 seconds,
the unit switches back to TV operation.
in display.
If no video cassette has been loaded, the clock
symbol blinks.
4F37001A (E)P20-BACK 5/6/2002, 16:41 20