manualshive.com logo in svg

AJA Ki PRO mini, Installation & Operation Manual

Share
Download
AJA Ki PRO mini Installation & Operation Manual Download Page 45

KiPro Mini v4.2

www.aja.com

45

 

14.1 ENCODE TYPE

This parameter defines the Apple ProRes encoding method if ProRes has been selected 
as the encoding mode. These are the options:

Or the following appears if 14.0 Encode Mode has been set to DNxHD. (These selections 
are valid only if an HD source is used—1080p for DNxHD 36.)

Note:

Note: Unlike Apple ProRes 422, Avid DNxHD encoding does not provide support 

for standard definition video. If standard definition video is input and an Avid 
DNxHD encode type has been selected, a warning prompt will appear: "WARNING 
Change Encode Input not HD."

15.1 PLAY MEDIA

This parameter determines behavior during playback. These are the options:

15.2 LOOP PLAY

This parameter turns looped playback on and off. These are the options:

15.3 PLAYLIST

This parameter displays the name of the selected playlist. These are the options:

ProRes 422 (default)
ProRes 422HQ
ProRes 422LT
ProRes 422PX

Record media as Apple ProRes 422 files.
Record media as Apple ProRes 422 (HQ) files.
Record media as Apple ProRes 422 (LT) files.
Record media as Apple ProRes 422 (Proxy) files.

DNxHD 220x (default)
DNxHD 145
DNxHD 36

Record media as Avid DNxHD 220x files.
Record media as Avid DNxHD 145 files.
Record media as Avid DNxHD 36 files.

One (default)
All
Playlist

Plays one clip and then stops playback
All/Playlist—Plays the current clip and then continues playing 
the next clip on the Ki Pro Mini media or the playlist.  Note that 
with this setting, Ki Pro Mini will play all clips back regardless 
of format or framerate—but you may notice the video monitor 
reset for format/framerate changes.  If all clips are the same 
format and framerate or conversion is applied to the output 
for clips with the same Hz, then clips play out smoothly one 
after another.

OFF (default)
ON

Play clip(s) and then stop playback when complete
Play clip(s) and then loop back and repeat playback

variable

The name of the selected playlist appears. If no playlist is 
selected via the web UI controls, then no name appears. The 
user cannot select or create playlists from the front panel UI; 
these tasks are handled using the web UI.

USO 

RESTRITO

Summary of Contents for Ki PRO mini











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands