manualshive.com logo in svg

Aiwa TV-AN1410, Service Manual

Share
Download
Aiwa TV-AN1410 Service Manual Download Page 19

– 19 –

5-1.   VCO ADJUSTMENT    VCO (PIF) Adjustment /

Video Carrier Frequency Free Running Adjustment

Input signal : RF-Color bar

                               Input level : 90dB

µ

V

                               Broadcast CH/fc=45.75MHz

Mode : TUNER
Test point : INPUT/TP-102   IF   (TU101-PIN 11)

                            OUTPUT/TP-201   AFT   (IC301-PIN 44)

Adjustment point : L205/P-IF
Measuring instrument : Oscilloscope

                                                Pattern generator / Leader : LCG-404

1. Connect oscilloscope to TP-201.
2. Input specified level of RF signal to TP-102 and adjust L205 until

TP-201 voltage becomes 2.8V

±

0.3VDC.

5-2.   SIF ADJUSTMENT    Audio IF Modulation Adjustment

Input signal : AM/FM-SG  RF  OUT/4.5MHz - SIF

                               MOD  OFF
                               90dB

µ

V

• Simple adjustment method receives normal broadcasting.
Mode : TUNER
Test point : INPUT / TP-203 : IC301-PIN 52

                            OUTPUT / TP-202 : IC301-PIN 54

Adjustment point : L201/S-IF
Measuring instrument : Oscilloscope

                                               AM/FM-Signal generator

1. Connect oscilloscope to TP-202.
2. Input specified signal to TP-203 and adjust L201 until TP-202

voltage becomes 4.5V 

±

 0.2VDC.

5.

Tuner Adjustment:

Perform the following adjustment in case of replacing any adjustment element during the repair. Proceed with the following adjustments as well
as in the adjustment menu screen. If those adjustments are not completed on both sides, the required adjustment will not be registered even
thought the adjustment has been processed in the adjustment menu screen.

The components which will be affected due to the repair.
• VCO coil
• SIF coil

Summary of Contents for TV-AN1410





















Reviews:

No comments

Brands by name

Popular brands

Load more brands