background image

5

Subject to change without notice  |  83030000aUK – Translation of the original operating manual |  ait-deutschland GmbH

Contact

Addresses  for  purchasing  accessories,  for  servicing 

or  for  answers  to  questions  about  the  unit  and  this 

operating manual can be found on the internet and are 

kept up-to-date.

  www.ait-deutschland.eu

Warranty / Guarantee

For warranty and guarantee conditions, please refer to 

the purchase documents.

 NOTE

Please contact your dealer about all matters 

concerning warranties and guarantees.

8  Disposal

When decommissioning the unit, always comply with 

applicable laws, directives and standards concerning 

recovery, recycling and disposal.

Scope of delivery

 

● Storage tank

 

● 1 sensor for the regulator

1.  Inspect the delivery for outwardly visible signs of 

damage.

2.  Check to make sure that the delivery is complete. 

 

Any  defects  or  incorrect  deliveries  must  be 

claimed immediately.

9.1  Accessories

 IMPORTANT

Use only original accessories from the manu-

facturer of the unit.

10 

Transport, Installation, 

Assembly

Observe the following when performing all work:

 IMPORTANT

The  tank  must  be  installed  in  a  frostproof 

room, to prevent frost damage to the storage 

tank, pipe system and connections.

 NOTE

Install the storage tank as close as possible 

to the heat generator, to keep the heat losses 

as low as possible. Ensure the shortest pos-

sible pipe lengths to the load.

 IMPORTANT

The floor or ground at the place of installation 

must be dry, firm and able to safely support 

the weight of the tank.

In  the  case  of  wall-mounted  storage  tanks, 

the wall must have sufficient load-bearing ca-

pacity to safely carry the weight of the stor-

age tank when full.

  “Technical  Data",  page 7,  for  the  respective 

model

10.1  Transport to installation location

To  avoid  damage  during  transport,  transport  the 

storage tank  (secured on the wooden pallet) to its final 

installation location using a lifting truck.

 CAUTION

Make sure to secure tank against slipping 

during transport.

 CAUTION

The tank can tip over when being removed 

from the wooden pallet and during 

transport with a hand truck or lifting 

truck.  This can result in personal injuries 

and damage.

 

► Take  suitable  precautions,  which  prevent 

the tipping hazard.

 

► Dispose of the transport and packaging materials 

properly and under ecological aspects.

Summary of Contents for WPSK 40Split













Reviews: