AIS Aloft 120 Manual Download Page 1

Aloft 120 - 2019

www.ais-inc.com

P-INSALOFT120V2 Revision 03.07.2019

1

***READ ALL INSTRUCTIONS BEFORE USING***

For commercial use only.

Warning: Risk of Injury 

– Maximum load 275 lbs. 2 leg, 325 lbs. 3 leg

Electrical rating: 120V, 60Hz, 16 AMP

No more than 12 furnishings can be connected on one branch circuit.

IMPORTANT SAFETY INSTRUCTIONS

DANGER 

– To reduce risk of electric shock:

• Always unplug furnishing from the electrical out let before cleaning.

WARNING 

– To reduce the risk of burns, fire, electric shock, or injury to persons:

• Unplug from outlet before putting on or taking off parts.

• Close supervision is necessary when this furnishing is used by, or near children, invalids 

or disabled persons.

• Use this furnishing only for its intended use as described in these instructions. Do not 

use attachments not recommended by the manufacturer.

• Never operate this furnishing if it has a damaged cord or plug, if it is not working 

properly, if it has been dropped or damaged, or dropped into water. 

• Keep the cord away from heated surfaces.

• Never operate the furnishing with the air openings blocked. Keep the air openings free of 

lint, hair and the like.

• Do not use outdoors.

• To disconnect, turn all controls to the off position, then remove plug from outlet.

• Connect to a properly grounded outlet only. See grounding instructions.

• For loading always put heavier items at the bottom and not near the top in order to help 

prevent the possibility of the furnishing tipping over.

Summary of Contents for Aloft 120
























































Reviews: