background image

INSTALLATION INSTRUCTIONS  

WARNING! 

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO 

PERSONS, OBSERVE THE FOLLOWING:

 

Installation work and electrical wiring must be done by qualified persons(s) in accordance with 
all applicable codes and standards, including fire-rated construction. 

STEP 1 

The MAXXFAN Dome 

fan requires a 

minimum 6 1/4 inch diameter roof opening. If 
you are replacing another type already 
installed, remove the old existing roof vent. 
Remove all old roof sealant for a minimum 
of 2” entirely around the roof opening. 

STEP 2 

Prior to installing the 

MAXXFAN Dome 

in 

the roof opening, apply a continuous strip of 
BUTYL tape or equivalent to the underside 
of the flange in the groove provided. 

CAUTION! 

When installing your 

MAXXFAN Dome

 fan, only use a 

caulking/sealant compatible with the 
flange (plastic product) and the roof 
surface. DO NOT use materials 
containing solvents such as or similar to 
Xylene, Toluene, Methyl Ethyl Ketone 
(MEK), Acetate or Acetone as they can 
damage the flange. Also, Polysulfide 
(Thiokol) type sealants must be avoided.  
If in doubt, please contact the 
manufacturer of your RV. 

STEP 3 

When inserting the 

MAXXFAN Dome

 fan 

into the roof opening: 

  orient the fan with the button toward 

the front of the coach. 

  ensure that the fan wires are hanging 

to the inside of the coach. 

Center the fan in the opening.  

Using the eight (8) screws provided, attach 
the flange to the roof at each dimple location 
along the flange. 

Note: Opening the fan lid gives better 
access to the flange for assembling the 
screws. 

Screw into the dimple to pierce the flange, 
making sure not to overtighten the screws to 
avoid cracking the flange. 

STEP 4 

After the 

MAXXFAN Dome

 fan has been 

installed, remove the excess BUTYL caulk 
that may have squeezed out. Using a sealer 
such as Dicor self-leveling lap sealant or 
similar caulking, apply a daub over every 
exposed screw head. In addition, apply a 
bead (approximately 3/16” dia.) along the 
outside edge of the flange all the way 
around the fan. 

THIS COMPLETES THE ROOF TOP 

PORTION OF THE INSTALLATION 

Summary of Contents for MAXXFAN DOME Series









Reviews: