background image

En-2

2.3. Accessories

 

WARNING

  For installation purposes, be sure to use the parts supplied by the manufacturer or 

other prescribed parts. 

  The use of non-prescribed parts can cause serious accidents such as the unit to fall, 

water leakage, electric shock, or 

fi

 re.

  The following installation parts are furnished. Use them as required.

  Keep the Installation Manual in a safe place and do not discard any other accessories 

until the installation work has been completed.

Do not discard any accessories needed for installation until the installation work has been 
completed.

Name and Shape

Q’ty

Application

Operating Manual

1

Installation Manual

1

(This book)

Cable tie (Large)

5

For fixing the connection pipe (Large 
and Small) and drain cap

Cable tie (Medium)

3

For transmission and remote 
controller cable binding

Coupler heat insulation 
(Small)

1

For indoor side pipe joint (Small)

Coupler heat insulation 
(Large)

1

For indoor side pipe joint (Large)

Special nut A
(Large flange)

4

For suspending the indoor unit from 
ceiling

Special nut B
(Small flange)

4

Hanger

4

For suspending the indoor unit from 
ceiling

Drain hose 

1

For installing drain pipe
VP25 (O.D.32, I.D.25)

Hose band

1

For installing drain hose

Drain hose insulation

2

Insulates the drain hose and drain 
cap

Wire

1
2
3

4
5

1

Attached only ARXB24/30/36/45L 
model. 
Use for static pressure under 40 Pa. 

2.4. Optional parts

When connecting the square duct and round duct, use the optional square flange or 
round 

fl

 ange.

Square 

fl

 ange

Model name : UTD–SF045T (P/N 9098180007)

1,063 mm

40 mm

206 mm

Round 

fl

 ange

Model name : UTD–RF204 (P/N 9093160004)

85 mm

ø195 mm

ø205 mm

ø225 mm

ø235 mm

Long-life 

fi

 lter

Model name : UTD–LF25NA (P/N 9079892004)

507 mm

239 mm

Other optional parts

Description

Model No.

Application

External output wire

9379529013

For output port

External input wire D

9368779016

For control input port
(Apply voltage terminal)

External input wire F

9368779023

For control input port
(Dry contact terminal)

External input wire B

9368778002

For forced thermostat off port
(Apply voltage terminal)

External input wire E

9368778019

For forced thermostat off port
(Dry contact terminal)

Remote sensor

UTD-RS100

Room temperature sensor

IR receiver unit

UTB-*WC

For the wireless remote 
controller.

Drain pump unit

UTZ-PX1NBA

When installing, please refer to the installation manual of each optional part.

9373385141-01_IM.indb   Sec1:2

9373385141-01_IM.indb   Sec1:2

7/12/2012   11:16:07 AM

7/12/2012   11:16:07 AM

Summary of Contents for ARXA24GALH



















Reviews: