En-2
2.3. Accessories
WARNING
For installation purposes, be sure to use the parts supplied by the manufacturer or
other prescribed parts. The use of non-prescribed parts can cause serious accidents
such as the unit falling, water leakage, electric shock, or
fi
re.
The following installation parts are furnished. Use them as required.
Keep the Installation Manual in a safe place and do not discard any other accessories
until the installation work has been completed.
Name and Shape
Q’ty
Application
Operating Manual
1
Installation Manual
1
(This book)
Drain hose
1
For installing drain pipe
VP25 (O.D.32, I.D.25)
Hose Band
1
For installing drain hose
Drain hose insulation
1
Adhesive type
(220 × 100 mm)
VT wire
1
For
fi
xing the drain hose L 280 mm
Coupler heat insulation
(Large)
2
For indoor side pipe joint (Gas pipe)
Coupler heat insulation
(Small)
1
For indoor side pipe
joint (Liquid pipe)
Cable tie (Extra large)
4
For
fi
xing the coupler
heat insulation
Cable tie (Large)
2
Cable tie (Medium)
2
For power supply and
transmission and remote
controller cable binding
Special nut A
(Large
fl
ange)
4
For installing indoor unit
Special nut B
(Small
fl
ange)
4
For installing indoor unit
Installation
template
1
For positioning the indoor unit
Auxiliary pipe assembly
1
For connecting the piping
]
2.4. Optional parts
The following options are available.
Description
Model No.
Application
Drain pump unit
UTR-DPB24T
9050642000
Round duct
UTD-RF204
9093160004
External output wire
9379529013
For output port
External input wire D
9368779016
For control input port
(Apply voltage terminal)
External input wire F
9368779023
For control input port
(Dry contact terminal)
External input wire B
9368778002
For forced thermostat off port
(Apply voltage terminal)
External input wire E
9368778019
For forced thermostat off port
(Dry contact terminal)
External input (no voltage) wire
9368779009
For control input port
3. INSTALLATION WORK
Correct initial installation location is important because it is dif
fi
cult to move unit after it is
installed.
]1
3.1. Selecting an installation location
Decide the mounting position together with the customer as follows.
WARNING
Select installation locations that can properly support the weight of the indoor unit.
Install the units securely so that they do not topple or fall.
CAUTION
Do not install the indoor unit in the following areas:
• Area with high salt content, such as at the seaside. It will deteriorate metal parts,
causing the parts to fail or the unit to leak water.
• Area
fi
lled with mineral oil or containing a large amount of splashed oil or steam,
such as a kitchen. It will deteriorate plastic parts, causing the parts to fail or the unit
to leak water.
• Area that generates substances that adversely affect the equipment, such as sulfuric
gas, chlorine gas, acid, or alkali. It will cause the copper pipes and brazed joints to
corrode, which can cause refrigerant leakage.
• Area that can cause combustible gas to leak, contains suspended carbon
fi
bers or
fl
ammable dust, or volatile in
fl
ammables such as paint thinner or gasoline. If gas
leaks and settles around the unit, it can cause a
fi
re.
• Area where animals may urinate on the unit or ammonia may be generated.
Do not use the unit for special purposes, such as storing food, raising animals,
growing plants, or preserving precision devices or art objects.
It can degrade the quality of the preserved or stored objects.
Do not install where there is the danger of combustible gas leakage.
Do not install the unit near a source of heat, steam, or
fl
ammable gas.
Install the unit where drainage does not cause any trouble.
Install the indoor unit, power supply cable, transmission cable, and remote controller
cable at least 1 m away from a television or radio receivers. The purpose of this is to
prevent TV reception interference or radio noise. (Even if they are installed more than
1 m apart, you could still receive noise under some signal conditions.)
If children under 10 years old may approach the unit, take preventive measures so that
they cannot reach the unit.
Take precautions to prevent the unit from falling.
(1) Install the indoor unit on a place having a sufficient strength so that it withstands
against the weight of the indoor unit.
(2) The inlet and outlet ports should not be obstructed; the air should be able to blow all
over the room.
(3) Leave the space required to service the air conditioner.
(4) Install the unit where connection to the outdoor unit (or RB unit) is easy.
(5) Install the unit where the connection pipe can be easily installed.
(6) Install the unit where the drain pipe can be easily installed.
(7) Install the unit where noise and vibrations are not ampli
fi
ed.
(8) Take servicing, etc., into consideration and leave the spaces. Also install the unit
where the
fi
lter can be removed.
(9) Do not install the unit where it will be exposed to direct sunlight.
9367702107-02_IM.indb Sec1:2
9367702107-02_IM.indb Sec1:2
1/25/2013 3:51:34 PM
1/25/2013 3:51:34 PM
