manualshive.com logo in svg

Airspan AirHarmony-4400, Installation Manual

Share
Download
Airspan AirHarmony-4400 Installation Manual Download Page 19

AirHarmony-4400 (External Cavity Filters) Installation Guide 

UGD-D01186 

Airspan Commercial and Internal Use 

13 

 

Convention 

Element 

Caution 

Signifies a hazardous situation—if not avoided—can void 
the product warranty, and cause property damage. 
Describes how to avoid it. 

Important 

Provides necessary information to explain a task. 

Note 

Provides additional information. 

Tip 

Provides helpful hints. 

 

Document Organization 

Chapter 

Contents 

Introduction

 

Provides a comprehensive overview of AirHarmony-4400 and its 
installation. 

Getting Started

 

Provides workflows for initial install and workflow. 

Verifying Prerequisites

 

Lists the hardware, software, and client requirements for 
installation. 

AirHarmony-4400 Installation

 

Describes how to install AirHarmony-4400. 

GPS Installation

 

Describes how to install the GPS antenna. 

Connect and Manage Cables

 

Describes how to connect the cables. 

Job Sheet

 

Provides information that aids users in performing the installation. 

Abbreviations

 

Lists the abbreviations used in this document and their expansions.  

Related Reading 

The following documents contain related information: 

AirHarmony-4400 Hardware Product Specification 

Airspan LTE Commissioning Manual 

 

 

Summary of Contents for AirHarmony-4400































































Reviews:

No comments

Brands by name

Popular brands

Load more brands