manualshive.com logo in svg

Airspan AirHarmony-4400, Installation Manual

Share
Download
Airspan AirHarmony-4400 Installation Manual Download Page 52

AirHarmony-4400 (External Cavity Filters) Installation Guide 

UGD-D01186 

Airspan Commercial and Internal Use 

46 

 

5.3

 

Cable Connections 

Note:

 The following images are for illustration purposes only. The actual tools or 

hardware may differ according to manufacturer. 

5.3.1

 

Copper Ethernet Cable Assembly 

The following demonstrates the recommended assembly instructions, hardware and tool 
requirements for the proper Ethernet cable assembly of the Ethernet Category 5e (enhanced) 
(CAT5e) cable used by Airspan products.  

The Ethernet cable is connected using a standard RJ45 connector protected by a harsh environment 
protective casing. 

Assembly Instructions 

The Copper Ethernet cable is connected to the AirHarmony-1000 using a Gland connector assembled 
on the bottom panel of the unit, as shown below. 

 

Figure 38: Gland connector - copper 

 

 

1.

 

Remove the Gland connector by unscrewing the body from the AirHarmony-1000, using 
the (supplied) Gland wrench. 

2.

 

Pass the prepared Ethernet cable through the tail nut, gland seal, body and front seal of 
the connector casing as shown below. Do not tighten the tail nut. 

 

Figure 39: Ethernet Cable through connector 

 

Summary of Contents for AirHarmony-4400































































Reviews:

No comments

Brands by name

Popular brands

Load more brands