Airspan AirHarmony-4400 Installation Manual Download Page 60 | Manualshive

Page: 60 / 62

Airspan AirHarmony-4400 Installation Manual Download Page 60

AirHarmony-4400 (External Cavity Filters) Installation Guide

UGD-D01186

Airspan Commercial and Internal Use

54

A

Job Sheet

This job sheet enables the users to keep track of their installation. It covers all the prerequisites
required for accomplishing the AirHarmony-4400 installation.

Table 12: Job Sheet

Site Requirements

Pole or wall for installation identified
Position on pole or wall identified
Pole access restrictions (highway regulations, other services on pole, power pole)
Method of reaching pole positions (ladders, Elevated work platform)
AC main fuse block available for AC/DC converter (where needed)
Configuration programming details known
Point of connection for Ethernet (if applicable)
All equipment items available at the installation site:

●

Main AirHarmony-4400 unit

●

External Filter Set – verify required set

●

GPS Antenna

●

Mounting bracket, through-bolt and pole clamps, or bolts if wall mount

●

Copper Ethernet or SFP cable assembly

●

Weather-proofing of the connections with a layer of self-amalgamating tape
followed by an over layer of PVC tape.

Tool Requirements
(For further information, see

Verify the Tools

.)

Large flat screw driver
Small flat blade screw driver (insulated shaft recommended)
Medium Philips head screw driver
13 mm wrench
Knife
pliers
Small side cutters
Wire strippers

Required Ancillary Equipment

Laptop PC for initial configuration
Cable for temporary connection of the laptop

Other installed materials

Cable ties
Labels (good to have)

«
...
58
59
60
61
62
»

Summary of Contents for AirHarmony-4400































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands