background image

4.  Wireless Settings 

 

 

 

EAP Certificate File:

 Click “Upload” to open a new window and select the location 

of an EAP certificate file to use. If no certificate file is uploaded, the internal RADIUS 
server will use a self-made certificate. 

 

 

Shared Secret: 

Enter a shared secret/password for use between the internal 

RADIUS server and RADIUS client. The shared secret should be 1 – 99 characters 
in length. This should match the “MAC-RADIUS” password used in 

IV-3-1-3-6 

or

 

IV-3-2-3

 

 

Session Timeout: 

Set a duration of session timeout in seconds between 0 – 86400. 

 

 

Termination Action: 

Select a termination-action attribute: “Reauthentication” sends 

a RADIUS request to the access point, “Not-Reathentication” sends a default 
termination-action attribute to the access point, “Not-Send” no termination-action 
attribute is sent to the access point. 

 
 

4.8.3  RADIUS Accounts 

The internal RADIUS server can authenticate up to 256 user accounts. The “RADIUS 
Accounts” page allows you to configure and manage users. 
 

37

 

              

AirLive  AC.TOP User’s Manual 

Summary of Contents for AC.TOP












































































Reviews: