2. Install two GU10 Base 6.5W maximum LED lamps by inserting lamp into socket and
turning clockwise slightly until firmly seated. DO NOT over tighten.
3. Remove any protective plastic adhered to the range hood.
4. Turn switches to the OFF ( • ) position and restore power. Test that the light and the fan
are operating properly.
5. If there is any vibration noise, check for the source and try to tighten fasteners or adjust
the tape to make a tighter connection or seal.
SECTION 7
Operation
Controls
Your Range Hood is equipped with two rotary switches with one controlling the lighting and
the other controlling the exhaust fan blower. The light switch has two positions, On and Off.
The fan switch has four positions, Off, High, Medium, and Low
(Figure 11).
SECTION 8
Maintenance
CAUTION:
MAKE SURE POWER IS SWITCHED OFF AT
SERVICE PANEL BEFORE SERVICING THE UNIT.
Grease Filters
Included with your range hood are aluminum grease filters that should be washed at least once
a month. The filters should be washed in a mild soap or detergent. Refer to
Step 3
of
Section 1
Preparing the Range Hood
, to remove filters. If the grease filters become damaged, replace with
Air King Model BCGF-01 Grease Filter.
Charcoal Odor Filter
If you have installed the optional charcoal odor filters, they cannot be washed and must be
discarded and replaced when they become noticeably dirty, have stopped filtering the odors, or
at least once per year. Replace with Air King Model BCCF-02 Odor Filters.
Changing the Lamp
Remove the lamp by turning slightly counter-clockwise and pulling out of the socket. Replace
with a GU10 Base 6.5W maximum LED lamp.
www.airkinglimited.com
6728027 Rev. T 3-17
4 of 12
Fuse
To replace the fuse, turn the fuse cap located next to the wire connector counter clockwise and
pull out. Replace with a Bussman MDA 125-Volt, 1.5 Amp Max. fuse. Reinstall the fuse back into
the hood.
Cleaning
CAUTION:
DO NOT USE GASOLINE, BENZINE, THINNER, HARSH
CLEANSERS, ETC., AS THEY MAY DAMAGE THE RANGE HOOD.
1. Clean your range hood with a mild detergent, such as dishwashing liquid, and dry with a soft
cloth.
NEVER USE ANY ABRASIVE PADS OR SCOURING POWDERS
. Completely dry before
restoring power.
NEVER IMMERSE ELECTRICAL PARTS IN WATER.
2. The fan assembly can be vacuumed when build up (dirt, lint, etc.) accumulates over time.
The fan is permanently lubricated and does not require oiling.
CALIFORNIA RESIDENTS ONLY:
WARNING:
THIS PRODUCT CAN EXPOSE YOU TO A CHEMICAL [OR
CHEMICALS] KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER.
WARNING:
THIS PRODUCT CAN EXPOSE YOU TO A CHEMICAL [OR
CHEMICALS] KNOWN TO THE STATE OF CALIFORNIA TO CAUSE REPRODUCTIVE
TOXICITY.
Troubleshooting Guide
Trouble
Probable Cause
Suggested Remedy
1. Hood does not operate when the switch is on.
1a. A fuse may be blown or a circuit tripped.
1a. Replace fuse or reset circuit breaker.
1b. Wiring is not connected properly.
1b. Turn off power to unit. Check that all wires are connected.
2. Hood is operating, but air moves slower than normal.
2.
Obstruction in the exhaust ducting.
2.
Check for any obstructions in the ducting including filter.
3. Hood is making a rattling noise.
3a. Filters are loose.
3a. Turn off power to unit. Check that all filter are securely in place.
3b. Duct connection is loose.
3b. Turn off power to unit. Check that duct connection is tight.
Installer:
Installation Date:
Place of Purchase:
Model Number:
Figure 11
