background image

Air Techniques, Inc.

Page 18

Configure the Intraoral Plate 
Guides. 

If the desired Plate Guides 

are not in place, install these Guides 
at this time . Do not operate the scanner 
without a full complement of two Guides 
in place .  Any combination of Guides 
may be used . See Figure 9 .

 

Figure 9 . ScanX with Plate Guides in Place .

ImaGInG pRocedURes

Scanner Track 2 

Plate Guide

Scanner Track 1 

Plate Guide

IMPORTANT:

Transfer the PSP from the PSP 

Transfer box to the Plate Guide slot 

quickly. Always keep the sensitive side 

away from any light source to minimize 

image loss.

Figure 10 .

PSP Pick-up .

Figure 11

Feeding Intraoral Plate .

Activate Scanner

Activate ScanX by performing the following procedures .

1 .  Make sure ScanX and computer components are correctly connected as shown in Figure 4 .
2 .  Switch the scanner from Standby to ON by pressing the membrane POWER switch (    ) located on 

the Keypad Control Panel on the top of the scanner .

3 .  Verify that both the green and blue LED indicators above the POWER and ERASER switches, 

respectively, illuminate . (Default mode has eraser ON .)

4 .  Use the user-supplied authorized Imaging Software to activate the Scanner and to select the desired 

image type and resolution . 

5 .  Verify that the two Scanner track indicators illuminate green when the Scanner has been activated, 

indicating that PSPs can be fed into the corresponding Plate Guide .

Scanning and Erasing Plates

Scan and erase an intraoral PSP in one operation by performing the following procedures .

1 .  Grasp a PSP by short edges between your thumb and index finger .  See Figure 10 .
2 .  With printed side facing you, carefully and quickly insert the PSP into the corresponding Plate Guide 

slot as far as possible . 

3 .  Immediately press the PSP all the way down with your fingertip (from position Figure 11 to position 

Figure 12) until the scanner's transport mechanism takes over and the PSP moves down on its own .

4 .  Verify that the track light illuminates yellow, indicating the Plate Guide slot is in use, the PSP has 

been sensed and the Scanner is transporting the PSP . 

Figure 12

Fully Inserted Plate .

Summary of Contents for ScanX Duo

































Reviews: