Air Live SI-108 User Manual Download Page 3

Copyright  and  Disclaimer 

 

                                                                                            ii

                                             

AirLive SI-108 User Manual

 

 

FCC Interference Statement 
 

This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against harmful interference in 
a residential installation. 
This equipment generates uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio 
communications. 
However, there is no guarantee that interference will not occur in a particular installation. 
If this equipment does cause harmful interference to radio or television reception, which can 
be determined by turning the equipment off and on, the user is encouraged to try to correct 
the interference by one of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

 
This device complies with Part 15 of the FCC Rules. Operation is subject to the following 
two conditions: 
(1)  This device may not cause harmful interference, and 
(2)  This device must accept any interference received, including interference that may 

cause undesired operation. 

 
FCC Caution: Any changes or modifications not expressly approved by the party 
responsible for compliance could void the user's authority to operate this equipment. 
This transmitter must not be co-located or operating in conjunction with any other antenna 
or transmitter. 
 
 

Disposal 

 

 

This marking indicates that this product should not be disposed with other 
household wastes throughout the EU. To prevent possible harm to the 
environment or human health from uncontrolled waste disposal, recycle it 
responsibly to promote the sustainable reuse of material resources. To 
return your used device, please use the return and collection systems or 
contact the retailer where the product was purchased. They can take this 
product for environmental safe recycling. 

Summary of Contents for SI-108

















Reviews: