manualshive.com logo in svg

Air Live POE-FSH2422G-390, User Manual, Page: 7 / 54

Share
Download
Air Live POE-FSH2422G-390 User Manual Download Page 7

1. Introduction 

AirLive POE-FSH2422G-390 User’s Manual 

 

2

1.2 Guide to the Chapters 

Chapter 1

     

Introduction and Quick Setup guide. All the essential information including IP Address and 
Password information are in the Quick Setup section. 

Chapter 2

     

Detail installation instruction including module information and how to make Cat. 5 cable 

Chapter 3

     

LED indicators 

Chapter 4

   

Detail information on Web management including how to setup remote management. 

1.3 Quick Setup 

This section provides the essential information for experienced users to operate the switch 
immediately. For detailed installation instruction, please see chapter 2 for more information. 

 
Power-On the switch 

„

 The 

POE-FSH2422G-390

 Switch has a built-in power supply to operate with 100 ~   

  240V AC, 50 ~ 60Hz power source.   

„

  The AC power cord connector is located at the rear of the unit and the On/Off switch is   

  next to the connector. 

„

  After the Switch is powered on, it will perform “self-diagnostic” test. This process takes   

  about 10 seconds to complete. 

 

„

 

It is recommended that you install the switch with an UPS to   
protect from potential power surge. 

The default password is 

airlive

 

„

 

This switch is using 48V 802.3af PoE standard. It does not work 
with passive PoE. Do not connect with passive PoE devices.   

The default IP address: 192.168.2.1 
The default username is 

admin

 

Important Information

 

 

 

 

 

 

 

 

 
 

Summary of Contents for POE-FSH2422G-390























































Reviews:

No comments