manualshive.com logo in svg

Air Live POE-FSH2422G-390, User Manual, Page: 23 / 54

Share
Download
Air Live POE-FSH2422G-390 User Manual Download Page 23

4. Web Management 

 
 
 
 
 

 

AirLive POE-FSH2422G-390 User’s Manual 

 

18

Direct Connection to Internet 

 

 

 

If you have a fixed IP xDSL account or cable modem account, and there is no router in the 
network, you can connect your switch directly to Internet via xDSL modem/Cable Modem. 
However, this method is not recommended as the LAN will be directly exposed to the 
Internet. 
 

Fixed IP

: If your ISP has assigned you a fixed IP. Please go to the Switch’s IP configuration 

and enter the IP address, Subnet Mask, and Gateway information offered by your ISP. If 
your ADSL connection is PPPoE or PPTP type, you have to connect through a router for 
remote management. 
 

Cable Modem

: If your Cable service provider uses DHCP for IP assignment, please turn on 

the DHCP function under IP configuration. Make sure there is no DHCP server in the 
network. Then the Cable provider will assign the switch with a IP and Gateway. Please 
contact with your ISP for further information about your IP address. 
 
When the configuration is finished, the Remote PC can access the switch by typing the 
switch’s IP address on the web browser. 

 

Connect through Broadband Router 

 

 

 

Summary of Contents for POE-FSH2422G-390























































Reviews:

No comments