manualshive.com logo in svg

Air Live BU-3026, User Manual

Share
Download
Air Live BU-3026 User Manual Download Page 13

2. Package Contents and Installation 

 
 

 

 

AirLive BU-3026/BU-3026-IVS User’s Manual

 

9 

1.  DC Jack: The input power is DC 12V. 
If you don’t have the PoE switch, you can use a power adapter to provide power to camera. 
 
2.  PoE/RJ45 LAN Socket: Connect to PC or Hub/Switch. 
This Ethernet port built N-Way protocol can detect or negotiate the transmission speed of 
the network automatically. Please use Category 5 cable to connect the Network Camera to 
a 100Mbps Fast Ethernet network switch or hub. 
 
3.  Alarm Digital I/O:   
AirLive BU-3026/BU-3026-IVS supports RS-485, 2 digital alarm inputs and 1 digital alarm 
output. Please make sure the alarm connections are properly wired. Please refer to the pin 
definition table below. 

 

PIN

 

SPECIFICATION 

1 

RS-485 D+ 

2 

RS-485 D- 

Compliant to RS-485 

3 

Ground (Common) 

GND 

4 

GPIO Out   

Close circuit current maximum: 
70mA AC or 100mA 
Output resistance: 30 ohm 
Open circuit voltage maximum: 
240V AC or 350V DC 

5 

GPIO In #1 

6 

GPIO In #2 

Action high voltage: 9~40 VDC 
Dropout voltage: 0 VDC 

 

4.  Audio Output: 3.5mm phone jack. 

 

5.  Audio Input: 3.5mm MIC jack. 
 
6.  MicroSD Card Slot: MicroSD Card Slot allows you to insert a memory card for 

expansion of storage. 

 
7.  Reset Button: This button is used to restore all the factory default settings. Sometimes, 

restarting the device will make the system back to a normal state. 

Summary of Contents for BU-3026

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands