background image

7.3 Speed read from wheel sensors

EVO4S has two wheel speed inputs: to
connect two speed sensors use the proper
split cable with part numberV02549030.

The digital sensor X02SNVM00 detects
the presence of a metallic tooth placed at
a distance between 0.5 and 2 mm.

Please use the software RaceStudio3 for
configuring the system.

Just enter the program configuration panel
and, after enabling the desired speed
channels, set the wheel circumference and
the number of pulses per revolution.

7. Speed 

EVO4S can receive the speed signal from
three different sources:

from the ECU

from the GPS receiver included in the kit

from the wheel sensors (digital channels)

It is therefore possible for EVO4S to receive
and store different values of speed at the
same time; the more powerful ECUs 
transmit up to four wheel speed values. 

7.1 Speed read from the ECU

If your ECU sends the value of speed in its
data stream, it is obviously possible to read,
record and show that value. 
Simply enable it using RaceStudio3 
software, as explained in section 10.1.1

7.2 Speed read from the GPS receiver

The GPS receiver you find in EVO4S kit is
configured in order to obtain the best
performance in terms of reactivity and
accuracy.
For getting GPS speed, you don’t need
any configuration. 
Simply  connect  the  GPS  Module  to  your
EVO4S and after a setup period of some se-
conds, the data will be received and auto-
matically recorded.

CHAPTER  8       ANALOG INPUTS

14

15

EVO4S

CHAPTER  7       SPEED 

8. Analog Inputs

0-5 Volt signals

ratiometric potentiometers 

pressure sensors

thermo-resistances 

K-type thermocouples

EVO4S  has 5 analog inputs, recorded up to
1000 times per second each. 
You can connect:

Please  use  the  following  steps,  using  the
software RaceStudio3 as explained in 
section 10.1:

connect the sensor to the desired input

enable the channel in the Channels table 

n

select the proper sensor type; sensors of
many different types are properly handled

set the sampling frequency

set the unit of measure.

EVO4S.qxp_Layout 1  09/01/17  10:22  Pagina 15

Summary of Contents for EVO4S























Reviews: