4
4.3.1Parts List
Mounting Plate 2 - Flat Washers
Base Plate
2 - Neoprene Washers
2 - 1/4-20 Hex Bolts
MT9214 ColumnMount
Insert a 1/4-20 hex head machine bolt through the
MT9227 base plate and into the threaded insert on
either end flange of the MT9214.
3. To install a camera or camera/housing assembly:
a. Insert two (2) 1/4-20 bolts with flat washers from
the underside of the MT9227 mounting plate.
b. Thread into the underside of the camera or housing
and tighten securely.
4. To adjust the MT9227:
a. Observe the camera video on a monitor while mov-
ing the camera to the desired position.
b. Tighten securely both the base plate mounting bolt
and the two side bolts.
4.4 MT9237 Heavy Duty Adjustable Head
Bracket
Neoprene
Washer
Mounting
Plate
Base
Plate
Flatwasher
1/4"-20
Hex Bolt
4.3 MT9227 Adjustable Head Bracket
Top View
(Mounting Plate)
Side View
Bottom View
(Base Plate)
Tilt
Adjust
4.3.2 Assembly
1. Insert a neoprene washer between each side of the
mounting plate and base plate.
2. Line up each of the side holes; insert one 1/4-20 hex
head machine bolt with flat washer and screw into each
threaded hole in base plate.
3. Hand tighten side bolts until ready to install.
4.3.3 Installation
1. The MT9227 is intended for installation on a rigid mount-
ing surface by use of a bolt through the base plate.
2. To mount the MT9227 Adjustable Head Bracket to:
MT9216 Wall Mount
a. Use the 1/4-20 threaded mounting hole located in
the center of the slot pattern.
b. Insert a 1/4-20 hex head machine bolt through the
adjustable head and into the threaded insert in the
wall mount. The bolt should be 20 mm (3/4 in) long.
A lock washer and a flat washer must be used under
the head of the bolt.
MT9222 Wall Mount
a. Line up the hole in the MT9227 base plate with the
center mounting hole on the mounting bracket.
b. Insert a bolt with flat washer through the MT9227
base plate and mounting bracket. A 5/16-18 x 50
mm (2 in) long bolt (not supplied) is recommended
to fasten the MT9227 to the mounting bracket.
c. From the underside of the mounting bracket, use a
lock washer and nut to secure the MT9227. Leave
hand tight.
4.4.2 Installation
1. The MT9237 is intended for installation on a rigid
mounting surface by use of 4 x 3/8-16 x1” Hex Bolts
through the corners of the base plate.
2. To mount the MT9237 Heavy Duty Adjustable Head
Bracket to: MT9207, MT9214 and MT9224 Column
Mounts or the MT9216 and MT9222 Wall Mounts:
a. Line up the holes in the corners of the MT9237 base
plate with the slots in the mounting flange.
b. Insert a 3/8-16 x 1” hex bolt through the base plate
and mounting flange, using a 3/8” flat washer and a
3/8” spiral lock washer under the head of the bolt.
c. From the underside of the mounting flange, use a
3/8” flat washer and a 3/8-16 hex nut to secure the
MT9237 to the mounting flange.
d. Repeat steps ‘a’ through ‘c’ for all four holes in the
base plate.Tighten all bolts securely.
Note: Do not mount the MT9216 or the MT9222 in an
inverted position.
4.4.1 Parts List
8 - 3/8” Flat Washers
4 - 3/8” Split Lock Washers
4 - 3/8 x 16 x 1” Hex Bolt
4 - 3/8 x 16 Hex Nut
Bottom View (Base Plate)
Side View
Top View (Mounting Plate)
Top
Base (Bottom)
