background image

26 

ADJUSTING THE CONTROLS 

 

Warning - 

The rotor must not start turning before the related 

controls have been operated. This condition is achieved by means 
of  the  control  lever  adjusting  screws  (B,  Fig.41).  In  addition,  the 
lever that controls the cutter drive must start the cutter only after 
movement of no more than 8 mm (Fig.41). If the adjusting screws 
are insufficient to achieve this condition (adjusting screw at end of 
thread) contact an authorized service center. 

SEDIMENT CUP 

Cleaning 

 

WARNING  -

 

Gasoline  is  highly 

flammable  and  explosive,  and  you  can  be 
burned  or  seriously  injured  when  handling 
fuel. 

Stop  engine  and  keep  heat,
sparks, and flame away.

Handle fuel only outdoors.

Wipe up spills immediately.

1.

Move  the  fuel  valve  to  the  OFF
position,  then  remove  the  fuel
sediment cup and O-ring.

2.

Wash  the  sediment  cup  in
non-flammable solvent, and dry it thoroughly.

3.

Place  the  O-ring  in  the  fuel  valve,  and  install  the  sediment  cup.  Tighten  the  sediment  cup
securely.

4.

Move the fuel valve to the ON position, and check for leaks. Replace the O-ring if there is any
leakage.

SPARK PLUG 

Recommended 

Spark 

Plugs: 

BPR6ES 

(NGK) 

or 

W20EPR-U (DENSO). 
The  recommended  spark  plug  has  the  correct  heat  range 
for normal engine operating temperatures. 

  WARNING

    -

   

An  incorrect  spark  plug  can  cause 

engine damage. 

For  good  performance,  the  spark  plug  must  be  properly 
gapped and free of deposits. 

1.

Disconnect  the spark  plug cap,  and  remove  any
dirt from around the spark plug area. 

2.

Remove  the  spark  plug  with  a  13/16-inch  spark
plug wrench. 

3.

Inspect the spark plug. Replace it if damaged or
badly  fouled,  if  the  sealing  washer  is  in  poor 
condition, or if the electrode is worn. 

4.

Measure the spark plug electrode gap with a wire
type feeler gauge. Correct the gap, if necessary, 
by carefully bending the side electrode. 
The gap should be:

 

0.70 0.80 mm. 

5.

Install the spark plug carefully, by hand, to avoid
cross-threading. 

6.

After  the  spark  plug  is  seated,  tighten  with  a
13/16-inch  spark  plug  wrench  to  compress  the 
sealing washer. 

7.

When installing a new spark plug, tighten 1/2 turn
after  the  spark  plug  seats  to  compress  the 
washer. 

8.

When reinstalling the original spark plug, tighten

Summary of Contents for 5580/3 GP160


































Reviews: