background image

Installation, Operation & Maintenance                                                                         Parksafe Gas Detector 

 

 

Rev: 9   10-20 

4  

INSTALLATION 

   Planning 

 

Our detectors should be installed in areas at risk of gas accumulation. 
Take in to account the design of the air flow patterns within the parking zone area. Detectors should be 
installed in the correct orientation, as recommended by the manufacturer, and ease of access should be 
accounted for to allow for any bump tests and other forms of maintenance and identification. 

 

   Typical Location and Positioning 

 
Consider the coverage required and function of the area. Emphasis should be placed on airflow patterns 
and correct placement, not perceived detecting ranges. The target gas will only be identified when 
contact is made with the sensing element itself. 
Locations for Parksafe gas detectors will vary based on the intended application and target gas, they 
should be located near where hazardous gas could quickly accumulate and areas of identified 
consequential risk. The composition of the target gas and its density relative to air are used as the basis 
for the recommended height of gas detectors. These heights may vary based on air flow and temperature 
conditions in addition to the proposed application and location.  
 

 

Carbon Monoxide (CO) gas      Breathing Zone - 1700mm (5ft 6”) from ground level. 

 

Nitrogen Dioxide (NO

2

)

 

gas    

  

Low Level - 300mm (1ft) from ground level.  

 

Avoid conditions of any other environmental factors that could potentially impede the accuracy and 
operation of the detectors such as; condensation; vibration; temperature, pressure, the presence of other 
gases, electromagnetic interference and draft areas. 
 

   Typical Installation Arrangement 

 

 

 

The gas detectors are designed around a centralised Parksafe control panel of which the location also 
needs to be considered. The panel should be located away from the hazardous area that it is monitoring. 
Accessibility is required both for status observation and alarm purposes. 
 

   

Where connections may exceed 500 yards from one control panel – Contact your supplier!

 

The use of sound strobes are highly recommended! 

Summary of Contents for PARKSAFE GAS DETECTOR

















Reviews: