8
FIGURE 15
IMPORTANT:
Application rates shown in the chart are
affected by humidity and by the moisture content of
the material (granular and pellet). Some minor setting
adjustments may be necessary to compensate for this
condition.
OVERLAP
REFER
TO CHART
We do not recommend the use of any powdered lawn
chemicals, due to diffi culty in obtaining a satisfactory or
consistent broadcast pattern.
1. Determine approximate square footage of area to be
covered and estimate amount of material required.
2. Verify that the spreader motor turns on and off and that
the fl ow control is operating properly.
3. Make sure the fl ow control lever is in the off position
and the closure plate is shut.
4. Set the adjustable stop to the desired fl ow rate, keeping
the fl ow control arm in the off position. Refer to the
application chart on this page and the instructions
on the fertilizer bag to determine the proper fl ow rate
setting. The application chart is calculated for a vehicle
speed of 3 mph (100 ft. in 23 seconds). Faster speeds
require higher fl ow rate settings to maintain the same
application rate.
5. Fill the hopper with the material to be spread, breaking
up any lumps as you fi ll the hopper.
7. Start the vehicle in motion and then open the spreader
closure plate and fl ip the switch to "ON".
OPERATION
HOW TO USE YOUR SPREADER
SETTING THE FLOW CONTROL
1. Slide the Adjustable stop to the desired setting.
2. Move the Flow Control Lever forward until it snaps into
the Adjustable Stop, locking the lever at the desired
setting. See fi gure 14.
5
1
3
7
10
OFF
FLOW CONTROL LEVER
ADJUSTABLE STOP
FIGURE 14
STARTING THE SPREADER
1. Move the Flow Control Lever against the Adjustable
Stop and fl ip the "ON-OFF" switch to the on position.
STOPPING THE SPREADER
1. Move the Flow Control Lever to the "OFF" position. Make
sure that the switch is turned off by the Flow Control
Lever.
8. Shut the closure plate before turning or stopping.
9. To insure uniform coverage, make each pass so that the
broadcast pattern slightly overlaps the pattern from the
previous pass as shown in fi gure 15. The approximate
broadcast widths for different materials are shown in
the application chart on this page.
10. When broadcasting weed control fertilizers, make sure
the broadcast pattern does not hit evergreen trees,
fl owers or shrubs.
11. Heavy moisture conditions may require a cover over the
hopper to keep contents dry. The vinyl cover acts as a
wind and moisture shield, but should not be used as a
rain cover.
12. If fertilizer is accidentally deposited too heavily in an
area, soak the area thoroughly with a garden hose or
sprinkler to prevent burning of the lawn.
TYPE
FLOW SETTING
SPREAD
TYPE
FLOW SETTING
SPREAD
TYPE
FLOW SETTING
SPREAD
MATERIAL
3 MPH
WIDTH
MATERIAL
3 MPH
WIDTH
MATERIAL
3 MPH
WIDTH
FERTILIZER
TYPE
FLOW SETTING
SPREAD
MATERIAL
3 MPH
WIDTH
FERTILIZER
APPLICATION CHART
Powder
3 - 5
3' - 4'
Powder
3 - 5
3' - 4'
Powder
3 - 5
3' - 4'
Powder
3 - 5
3' - 4'
Granular
3 - 5
10' - 12'
Granular
3 - 5
10' - 12'
Granular
3 - 5
10' - 12'
Granular
3 - 5
10' - 12'
Pelleted
3 - 5
17' - 19'
Pelleted
3 - 5
17' - 19'
Pelleted
3 - 5
17' - 19'
Pelleted
3 - 5
17' - 19'
Organic
6 - 8
3' - 4'
Organic
6 - 8
3' - 4'
Organic
6 - 8
3' - 4'
Organic
6 - 8
3' - 4'
GRASS SEED
GRASS SEED
Fine
3 - 4
3' - 4'
Fine
3 - 4
3' - 4'
Fine
3 - 4
3' - 4'
Fine
3 - 4
3' - 4'
Coarse
4 - 5
8' - 9'
Coarse
4 - 5
8' - 9'
Coarse
4 - 5
8' - 9'
Coarse
4 - 5
8' - 9'
ICE MELTER
6 - 8
17' - 19'
ICE MELTER
6 - 8
17' - 19'
ICE MELTER
6 - 8
17' - 19'
ICE MELTER
6 - 8
17' - 19'
SAND
4-10
17' - 19'
SAND
4-10
17' - 19'
SAND
4-10
17' - 19'
SAND
4-10
17' - 19'
OPERATING SPEED
- 3 MPH. (100 ft. in 23 seconds)
