background image

2

RULES FOR SAFE OPERATION

The  following  safety  precautions  are  suggested.  This
broadcast spreader is designed, engineered and tested
to offer reasonably safe and effective service, provided
it is operated in strict accordance with these instructions.
Failure  to  do  so  may  result  in  personal  injury.  Always
observe the rules of safe operation.

1.

Do  not  allow  anyone  to  operate  the  broadcast
spreader without proper instructions.

2.

Do  not  permit  children  to  operate  the  broadcast
spreader.

3.

Wear eye and hand protection when handling and
when applying lawn or garden chemicals.

4.

Read the chemical label instructions and cautions
for handling and applying the chemicals purchased
for spreading.

5.

Keep  all  nuts,  bolts  and  screws  tight  to  be  sure
equipment is in safe working condition.

6.

Follow maintenance and lubrication instructions as
outlined in this manual.

LOOK FOR THIS SYMBOL TO POINT OUT
IMPORTANT SAFETY PRECAUTIONS. IT
MEANS -- ATTENTION!  BECOME ALERT!
YOUR SAFETY IS INVOLVED.

Your broadcast spreader carton contains parts as shown on pages 2 and 3.  Identify all parts and lay out as
shown.

CARTON CONTENTS

LOOSE PARTS IN CARTON

1.

Handle Tube (long)

2.

Braces

3.

Flow Control Mount Bracket

4.

Flow Control Arm

5.

Handle Tube (short)

6.

Flow Control Rod

7.

Leg Stand Tube

8.

Wheels (R.H. & L.H.)

9.

Hopper Assembly

10. Hardware Package (not shown)

2

6

5

1

7

9

3

4

8

Summary of Contents for 45-02102













Reviews: