manualshive.com logo in svg

Agora Models Bismarck 06, Build Instructions

Share
Download
Agora Models Bismarck 06 Build Instructions Download Page 24

04

. ASSEMBLING THE SEARCHLIGHT PLATFORM

07

08

03

04

Apply a little superglue to the peg on the searchlight 
base 

F

 and fix it into the recess in the centre of the 

support arm 

E

 (see arrow).

Glue the searchlight base 

C

 to the underside of the 

searchlight stand 

F

 (inset). Repeat this section of 

steps to assemble the second searchlight.

When you are happy with the fit, apply a little 
superglue to the underside of the decking and fix in 
place. Make sure there is no glue on the cables.

Gently pull the cables 

63-11

 so that the headlight 

stands 

C

 are drawn towards the decking. Apply a little 

superglue to the underside of the stands and fix them 
on the decking as shown. 

01

02

Take the deck covering 

63-03

. Thread the connectors 

on the ends of the searchlight cables through the two 
holes in the deck covering. 

Position the deck covering on the searchlight 
platform 

63-05

 so that the cables run through the 

recesses in the platform (see arrows). 

63-13

63-12

63-11

63-05

F

E

C

F

63-03

63-03

63-03

63-05

63-11

C

24

24

AGORA

MODELS

25

AGORA

MODELS

Summary of Contents for Bismarck 06








































Reviews:

No comments

Brands by name

Popular brands

Load more brands