manualshive.com logo in svg

Agora Models Bismarck 06, Build Instructions

Share
Download
Agora Models Bismarck 06 Build Instructions Download Page 17

61-01

PWB

PB 

1.7 x 6

61-08

22-01

22-02

61-04

61-03

61-09

61-08

61-08

22-01

61-08

61-04

22-01

03

01

03

Take the large upper deck assembly 

19-01/22-01/48-

01

. Identify and position of the gun turret assembly on 

the barbette 

22-02

, as shown.

Holding the gun turret in place, carefully turn the deck 
assembly over. Fit the cog 

61-04

 on the base plate 

61-03

 with the tab on part 

61-03

 fitting in the notch in 

part 

61-04

. Fix in place with three 

PB

 1.7 x 6mm screws.

Fix the switch 

61-08

 to the underside of the upper 

deck 

22-01

 using a 

PWB

 2.3 x 4mm screws

04

02

. FITTING THE SWITCH

Take the cable 

61-08

 and wrap the cable label  

61-09

 around the end of the cable near the  

connector, as shown. 

On the underside of the deck assembly, identify the 
recess for the switch 

61-08

 in the recess in deck 

section 

22-01

 (arrow). 

Fit the switch 

61-08

 into the recess in the upper 

deck, so that the long white arm is near the cog 

61-04

 (arrow).

04

02

17

17

AGORA

MODELS

18

AGORA

MODELS

Summary of Contents for Bismarck 06








































Reviews:

No comments

Brands by name

Popular brands

Load more brands