background image

© 201

9

 Agnetix Inc. All Rights Reserved. Specifications subject to change 

7965 Dunbrook Road - Suite I - San Diego, CA 92126

2

agnetix.com

Agnetix

Product Guide – Specifications & Installation

Agnetix A3 1200

CONTROL

Network

4 x 100Mb POE Ethernet

Connectors

4 x Waterproof 13/16 RJ45

Dimming

Down to 1%

ENVIRONMENTAL

Operating Conditions

-20°C(-4ºF) to 60°C (140ºF)/ RH <95%

Storage Conditions (no liquid)

-20°C(-4ºF) to 80°C (176ºF) / RH <95

IP

IP66 Wash Down

WATER LOOP/COOLING 

*Protect From Freezing - or - Use Antifreeze

Fluid Temperature Limits

-20°C(-4ºF) – 75°C (167ºF )

Fluid Temperature Recommended

Dew point up to 40°C (104ºF)

Self Protection

65°C (149°F) (full light) to 75°C (167°F) (no light)

Max Fluid Temp when using light for Heat

75°C (167°F)

Fluid Connection

Twin Exposed 1/2” Copper Tubing
Push to Connect
Do not solder or crimp

Flow Rate

1 to 3 gpm per tube

Temp Rise

Depends on flow rate

Power Delivered to Water

~600W

DIMENSIONS (INCHES)

*LED Module for A3-1200-DD contain different LED pattern with twice the LED count

Light Spine mounting system

5.0

.25

.25

3

8

 x 

7

8

 

3.7

2.0

2.0

3.33 Nominal

40 Nominal

36.5

5.12

14.0

2.0

Downward USB

Port #1

RJ-45 Ethernet

Network Port

w/ POE

RJ-45 Ethernet

Network Port

w/ POE

USB

Port #2

7

8

Power Cable System

Connection

LED Module #2

LED Module #1

LED Module #3

RJ-45 Ethernet

Network Port

w/ POE

1

2

" Copper Tubing

Do Not Solder or Crimp

Light Spine mounting system

5.0

.25

.25

3

8

x

7

8

3.7

2.0

2.0

3.33 Nominal

40 Nominal

36.5

5.12

14.0

2.0

Downward USB

Port #1

RJ-45 Ethernet

Network Port

w/ POE

RJ-45 Ethernet

Network Port

w/ POE

USB

Port #2

7

8

 Power Cable System

Connection

LED Module #2

LED Module #1

LED Module #3

RJ-45 Ethernet

Network Port

w/ POE

1

2

" Copper Tubing

Do Not Solder or Crimp

Light Spine mounting system

5.0

.25

.25

3

8

x

7

8

3.7

2.0

2.0

3.33 Nominal

40 Nominal

36.5

5.12

14.0

2.0

Downward USB

Port #1

RJ-45 Ethernet

Network Port

w/ POE

RJ-45 Ethernet

Network Port

w/ POE

USB

Port #2

7

8

Power Cable System

Connection

LED Module #2

LED Module #1

LED Module #3

RJ-45 Ethernet

Network Port

w/ POE

1

2

" Copper Tubing

Do Not Solder or Crimp

*

Summary of Contents for A3 1200









Reviews: