manualshive.com logo in svg

Agilent Technologies U1270 Series, Service Manual

Share
Download
Agilent Technologies U1270 Series Service Manual Download Page 27

Calibration Procedures

1

 

Performance Verification Tests

U1270 Series Service Guide

27

Performance Verification Tests

Use the performance verification tests to verify the 
measurement performance of the instrument. The 
performance verification tests use the instrument's 
specifications listed in the 

U1271A/U1272A User's Guide

 and 

the 

U1273A/U1273AX User’s Guide

 (available for download at 

www.agilent.com/find/hhTechLib

). 

The performance verification tests are recommended as 
acceptance tests when you first receive the instrument. The 
acceptance test results should be compared against the 

 

1 year test limits. After acceptance, you should repeat the 
performance verification tests at every calibration interval. 

If the instrument fails the performance verification tests, 
adjustment or repair is required.

N O T E

Ensure that you have read the 

“Test Considerations” 

on page 26 before 

running the performance verification tests.

Summary of Contents for U1270 Series


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands