manualshive.com logo in svg

Agilent Technologies PSA E4446A, Installation Note

Share
Download
Agilent Technologies PSA E4446A Installation Note Download Page 9

Installation Note 

E4440-90632

9

Installation Procedure

Uninstalling Option 1DS

1. Locate the RF section on the right side of the instrument. 

Figure 3

 shows cable 

locations and the preamplifier mounting orientation.

Figure 3

Preamplifier Location

2. Locate and remove cable W55 (SBTX to FIFA rear connector), E4446-20045. This 

cable will be replaced later. It is removed to allow the preamplifier assembly to be 
removed.

3. Locate and remove cable W56 (FIFA front connector to Band Pass filter), 

E4446-20046. This cable will be replaced later. It is removed to allow the preamplifier 
assembly to be removed.

4. Locate and remove cable W39 (low band assembly J4 to band pass filter), 

E4446-20058, using the 5/16-inch wrench. This cable will be replaced later. It is 
removed to allow the preamplifier assembly to be removed.

5. Locate and remove cable W50 (preamplifier J2 and low band assembly J1 RF IN). 

Discard this cable, since it will be replaced by another cable.

Summary of Contents for PSA E4446A































Reviews:

No comments

Brands by name

Popular brands

Load more brands