manualshive.com logo in svg

Agilent Technologies n5181a, Service Manual, Page: 188 / 202

Share
Download
Agilent Technologies n5181a Service Manual Download Page 188

Agilent Technologies N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

 

 

Post-Repair Procedures and Performance Verification
Performance Verification

4-8

Performance Verification

The procedures in this chapter verify the signal generators electrical performance. 

•

“I/Q Calibration (N5162A/82A only)” on page 4-8

•

“Running Self Test” on page 4-8

•

“Relative Frequency Range and Accuracy Verification (N5161A/62A

1

/81A/82A Only)” on page 4-10

•

“Leveled Output Power Verification (N5161A/62A

1

/81A/82A Only)” on page 4-13

I/Q Calibration (N5162A/82A only)

When you perform an I/Q calibration, that calibration data takes precedence over the factory-supplied calibration data. The calibration 
routines improves performance that may degrade over time or due to temperature changes. 

Running Self Test

The self test is a series of internal tests of signal generator functions. Run the complete self tests when initially setting up a signal generator, 
after an assembly repair, or to verify signal generator performance. Also run self test prior to performing manual or automated Performance 
Verification tests. The self test will confirm the signal generator is operating properly or isolate problems to a specific faulty assembly.

Press

 I/Q

 >

 I/Q Calibration 

> 

Calibration Type Full

It takes about 5 minutes to run the self test. 

This information is 

supplemental

. 

Please disregard 
unless 

Agilent 

specifically 

requests 

this information.

深圳德标仪器 

135-1095-0799

Summary of Contents for n5181a











































































































































































































Reviews:

No comments