manualshive.com logo in svg

Agilent Technologies n5181a, Service Manual, Page: 190 / 202

Share
Download
Agilent Technologies n5181a Service Manual Download Page 190

Agilent Technologies N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

 

 

Post-Repair Procedures and Performance Verification
Relative Frequency Range and Accuracy Verification (N5161A/62A

1

/81A/82A Only)

4-10

Relative Frequency Range and Accuracy Verification (N5161A

1

/62A

1

/81A/82A Only)

The frequency range is tested by determining the frequency accuracy relative to the timebase at the frequency limits of the signal generator. 
This test can be performed with either a frequency counter 

or

 a spectrum analyzer.

•

“Frequency Counter Procedure (N5161A/62A/81A/82A)” on page 4-10

 

or

•

“Spectrum Analyzer Procedure (N5161A/62A

1

/81A/82A)” on page 4-11

Frequency Counter Procedure (N5161A/62A/81A/82A)

Test Setup

1.

Connect the equipment as shown.

2.

Preset the signal generator: Press 

Preset

.

3.

Turn modulation off: Press the 

Mod On/Off

 so that the MOD On/Off LED turns off.

4.

Set the amplitude: 

 

Press 

Amplitude

 and enter 0 dBm.

5.

Turn RF on: Press 

RF On/Off

 so that the RF On/Off LED lights.

6.

Verify that the frequency counter is locked to the 10 MHz external reference frequency (±1 Hz).

7.

For maximum accuracy, set the gate time on the frequency counter to >5 seconds. 

 

(Press 

Gate & ExtArm

 twice and use the arrow keys to set the value.)

8.

Set the frequency: Press 

Frequency

 and set the signal generator to the first frequency listed in 

Table 4-7

.

9.

Confirm that the measured frequency is within the limits listed.

10. Repeat step 

8

 and step 

9

 for all of the frequencies in the table that are within the frequency range of your signal generator.

NOTE

For frequencies <200 MHz, use Channel 3 on the frequency counter 

 

(press 

Freq Ratio

 until 

CH3:

 displays).

1

The N5161A/62A performs the identical internal tests as in the MXG via a LAN connection to a Web Server.  The front panel displays all hardkeys, softkeys and test results 

as depicted in the illustration. For information on Web-Enabled Control refer to 

“Accessing the MXG Web-Enabled Page” on page 1-18

 and to the 

Programming 

Guide.

 

Table 4-6 Recommended Equipment for Checking N5161A/62A/81A/82A Frequency Range and Accuracy

Test Equipment

Recommended Model

Frequency Counter

Agilent 53131A/32A Universal Counter

深圳德标仪器 

135-1095-0799

Summary of Contents for n5181a











































































































































































































Reviews:

No comments