Agilent Technologies n5181a Service Manual Download Page 186

Page: 186 / 202

Agilent Technologies N5161A/62A/81A/82A/83A MXG Signal Generators Service Guide

Post-Repair Procedures and Performance Verification
Post Repair Procedures

4-6

Adjustments (N5183A Only)

To ensure the signal generator is meeting all published specifications,

Table 4-4

lists the adjustments that must be performed after a specific

assembly has been repaired or replaced.

Download the service software from

http://www.agilent.com/find/calibrationsoftware

or you can purchase the software on a CDROM (a

license is required to run the calibration software).

Automated Performance Verification Tests

For the N5161A/62A/81A/82A:

Table 4-5

lists the automated service software performance verification tests that should be performed to

confirm the instrument still meets its warranted specifications. Run these tests at least every 24 months or more often as necessary.

For the N5183A:

Table 4-5

lists the automated service software performance verification tests that must be ran after any repair or to confirm

the instrument still meets its warranted specifications. Run these tests at least every 24 months or more often as necessary.

Download the service software from

http://www.agilent.com/find/calibrationsoftware

or you can purchase the software on a CDROM (a

license is required to run the calibration software).

If an automated performance verification test fails, go to

“Troubleshooting Performance Test Problems” on page 1-72

to troubleshoot the

instrument failure.

Table 4-4 Adjustments

Adjustments

Adjusted

Assembly

A3 RF Assem

A7 MW Assem

MW Multiplier Pre-level Calibration

AM Calibration

Limited Absolute Power Calibration

ALC Mod Driver

Assembly requiring adjustment is determined by the type of failure

(i.e. low band (A3 RF Assembly) or high band (A7 MW Assembly)).

Table 4-5 Automated Performance Verification Tests

N5161A
N5181A

N5162A
N5182A

N5183A

Automated performance verification tests are listed in the order they should be performed to prevent invalid results and to minimize changes in
test equipment configurations.

Digital Modulation Power Level Accuracy Relative to

Maximum Leveled Power

Power Level Accuracy

Harmonic Spurious

Sub-Harmonic Spurious

Non-Harmonic Spurious

WCDMA Adjacent Channel Power

FM Deviation Accuracy

FM Distortion

Digital Modulation Quality

深圳德标仪器

135-1095-0799

Summary of Contents for n5181a











































































































































































































Search results

Summary of Contents for n5181a

Reviews:

Agilent Technologies n5181a, Service Manual, Page: 186 / 202

Search results

Summary of Contents for n5181a

Reviews: