Agilent Technologies N4970A User Manual Download Page 9 | Manualshive

Page: 9 / 30

Agilent Technologies N4970A User Manual Download Page 9

Getting Started

PRBS Generator 10 Gb/s User Guide

9

1

Getting Started

1.1

Unpacking and Installation

The N4970A PRBS generator 10 Gb/s is shipped with all the accessories

required for the self-test mode and verification.

The shipment includes:

•

N4970A PRBS generator 10 Gb/s

•

AC power converter module

•

AC power cord

•

CD containing the N4970A user guide and N4970A data sheet

If this product is not used as specified, the protection provided by the

equipment could be impaired. This product must be used in a normal

condition (in which all means for protection are intact) only.

Before switching on this instrument, make sure the supply voltage is in the

specified range.

This instrument has auto ranging line voltage input. Be sure the supply

voltage is within the specified range.

To prevent damage to the instrument, make all RF connections between the

N4970A and the DUT or test equipment BEFORE applying AC power to the

N4970A. Also, remove AC power from the N4970A instrument before

disconnecting any RF connections.

«
...
7
8
9
10
11
...
»

Summary of Contents for N4970A































Reviews:

No comments