manualshive.com logo in svg

Agilent Technologies N4906B Serial BERT, Getting Started

Share
Download
Agilent Technologies N4906B Serial BERT Getting Started Download Page 4

USB

Local

Preset

Power 

Supply

GPIB Port

USB 2.0 VISA Port

Operating the Agilent Serial BERT

Now that the instrument is running, let’s take a look at its front 
panel elements:

4

Instrument Setup Controls

Accumulation Controls

Keypad and 
Front Panel Knob 

PG Connectors

ED Connectors

ED Controls

PG Controls

Power Switch and 

Earth Terminal

PS/2 Keyboard

(purple)

PS/2 Mouse

(green)

Serial Port 1

Parallel Port

VGA Monitor

Ethernet Port 1/2

Audio Line 
Output Jack

Audio Microphone 
Input Jack

Diagnostic 
LED Stack

 USB 2.0 
Channel 0-3

The Agilent Serial BERT is available in different versions. Depending on your 
version, some of the hardware and functionality described in this brochure 
may not be available.

The rear panel of the instrument provides the following connectors:

To avoid damage to the Serial BERT and your devices under test, 
always use an ESD strap that is connected to the earth terminal.

Summary of Contents for N4906B Serial BERT













Reviews:

No comments

Brands by name

Popular brands

Load more brands