Agilent Technologies G1157A User Manual Download Page 14

Page: 14 / 78

Agilent 1200 Series Valves

Installation and Configuration

Software Configuration

The Agilent 1200 Series valves can be controlled by the Agilent ChemStation
Rev. A.09.03 or higher.

C A U T I O N

The maximum number of all modules (including CAN-slave valves) in your Agilent 1200
Series LC system must not exceed 13.

Contact your local sales and service representative to verify, if your configuration is
supported. This is especially important, if the number of module is close to 13.

To configure the Agilent 1200 Series valves

Step

Note

Start the Agilent ChemStation
Software.

Select

Configure 1200 Access

in the

Instrument

menu.

In the upcoming

Configuration

dialog

box select one or multiple valves and
click

Add.

The selected green valve icon now
moves from the left

Available Modules

panel to the right

Configured Modules

panel as displayed in

Figure 2

page 15

Click

to leave the

Configuration

dialog box.

After a

Restart

the Agilent

ChemStation Software a new menu
item

Setup Valve

now appears in the

Instrument

menu.

Summary of Contents for G1157A















































































Search results

Summary of Contents for G1157A

Reviews:

Related manuals for G1157A

Brands by name

Popular brands

Agilent Technologies G1157A, User Manual

Search results

Summary of Contents for G1157A

Reviews:

Related manuals for G1157A

Brands by name

Popular brands