manualshive.com logo in svg

Agilent Technologies ESA E4401B, Installation Note, Page: 8 / 10

Share
Download
Agilent Technologies ESA E4401B Installation Note Download Page 8

8

Installation Note E4411-90051

Remove Front Frame and Install Tracking Generator

8. Refer to Figure 3. Remove the two screws on the bottom side (1) of the instrument that secure the

front frame to the RF assembly.

9. Place the instrument with the top side facing up. Remove the two screws (2) that

secure the front frame subpanel to the chassis sides.

Figure 3. Remove Front Frame

10. Slide the front frame forward until it latches. Disengage the latches on each side of the instrument

by sliding the front frame back toward the instrument a small amount and then gently pulling out
on the latch tabs (3).

11.  Slide the front frame forward just far enough to reach the ribbon connector attached to J2 on the

front panel keyboard printed circuit board. Disconnect the ribbon cable from J2.

12.  Remove the front frame and position it with the display down. With a flat-blade screwdriver,

carefully press the side tab of the hole plug in the tracking generator RF Out connector hole (from
the inside of the front panel) and push the plug out of the hole. Discard the hole plug and set the
front panel assembly aside.

Summary of Contents for ESA E4401B











Reviews:

No comments