manualshive.com logo in svg

Agilent Technologies 83433A, User Manual, Page: 50 / 62

Share
Download
Agilent Technologies 83433A User Manual Download Page 50

3-19

Reference

Returning the Instrument for Service

rugated cardboard carton of 159 kg (350 lb) test strength. 

• The carton must be large enough to allow approximately 7 cm (3 inches) on 

all sides of the instrument for packing material, and strong enough to accom-
modate the weight of the instrument. 

• Surround the equipment with approximately 7 cm (3 inches) of packing ma-

terial, to protect the instrument and prevent it from moving in the carton. If 
packing foam is not available, the best alternative is S.D-240 Air Cap™ from 
Sealed Air Corporation (Commerce, California 90001). Air Cap looks like a 
plastic sheet filled with air bubbles. Use the pink (antistatic) Air Cap™ to 
reduce static electricity. Wrapping the instrument several times in this ma-
terial will protect the instrument and prevent it from moving in the carton. 

5

Seal the carton with strong nylon adhesive tape. 

6

Mark the carton “FRAGILE, HANDLE WITH CARE”. 

7

Retain copies of all shipping papers. 

Summary of Contents for 83433A































































Reviews:

No comments